LED retrofit
Convert old neon or fluorescent signs to low-draw, long-life LED, often cutting the power bill.
Sign repair and service in Edmonton,
even signs we didn't build.
Signs fail: faces crack, LEDs go dark, panels fade, transformers quit. We fix them fast, on signs we built and signs we did not, across the Edmonton area.
A dark sign is costing you customers
Every night a sign sits dark or half-lit, customers drive past. We diagnose the cause, give you a straight answer on repair versus replace, and fix it with our own crew and equipment. Because we fabricate signs ourselves, we can make replacement faces and parts in-house instead of waiting on a supplier.
What we build.
Re-lamp & power supply
Replace failed LED modules, ballasts, and transformers to bring a sign back to full, even brightness.
Face & tenant-panel swaps
New acrylic faces and tenant panels for cabinets and pylons when a business or brand changes.
Electrical & wiring repair
Diagnose and repair sign wiring, disconnects, and primary electrical so it passes inspection.
Pylon & cabinet refurbishment
Repaint, reskin, and re-light aging pylon and cabinet signs instead of full replacement.
Take-down & reinstall
Safe removal for building work, storage, and clean reinstallation when you are ready.
Best for Where this fits
- Signs that are dark, flickering, or only partly lit
- A new tenant moving into an existing cabinet or pylon slot
- Storm, wind, or vehicle damage to an existing sign
- High hydro bills from old neon or fluorescent signage
- Property managers maintaining signage across multi-tenant sites
- Faded or peeling faces and panels that make the business look closed
Good to know
- We assess first and tell you honestly whether a repair or a replacement is the better spend.
- Some electrical repairs require an electrical permit; we handle it where needed.
- An LED retrofit usually pays back through lower power draw and far longer lamp life than neon or fluorescent.
- We service signs across the Edmonton area whether or not Crown built them originally.
The details.
- Channel letters
- Re-lamp, LED retrofit, face and trim repair
- Cabinets & lightboxes
- Face and panel replacement, LED conversion, power supply swaps
- Pylon & monument
- Tenant-panel changes, repaint, re-light, structural touch-up
- Electrical
- Wiring, disconnects, transformers, and power-supply repair
- Response
- Local Edmonton-area crew with our own equipment
- Coverage
- Signs we built and signs we did not
One team handles the whole repair, start to finish.
We diagnose, repair, retrofit, and warranty, on the Edmonton area's signs, whether or not Crown built them.
- On-site diagnosisWe come out, find why the sign failed, and tell you what it actually needs.
- LED retrofitsWe convert old neon and fluorescent cabinets to low-draw, even LED.
- Face & panel replacementCracked faces, faded vinyl, and tenant-panel swaps, colour-matched to the original.
- Electrical & transformer repairPower supplies, wiring, and ballasts repaired to the Canadian Electrical Code.
- Re-lamping & cleaningWe bring tired signs back to full, even brightness.
- Permits where requiredIf a repair needs a development or electrical permit, we pull it.
- Warranty on our workRepairs are backed by Crown's workmanship warranty.
Signs like these, kept bright across Edmonton.
Brands that trust Crown.
Common questions.
Yes. A large part of our service work is on signs other companies built or that came with the building. We diagnose the issue, source or fabricate the parts, and repair it across the Edmonton area.
Almost always. Half-lit and flickering signs are usually failed LED modules, a dying power supply, or a wiring fault. We find the cause and repair it, and we can retrofit the whole sign to LED if the old lighting is at end of life.
We tell you straight after looking at it. If the cabinet and structure are sound, an LED retrofit is usually the better spend and cuts the power bill. If the sign is corroded or off-brand, replacement may cost less over time. You get the honest version either way.
Yes. When a tenant changes, we fabricate and install a new panel to fit the existing pylon or cabinet, matched to the sign criteria, usually without disturbing the other tenants' panels.
Let's build it
Get your sign lit, legible, and working again.
Free consultation and site survey, an honest quote, and one Edmonton team from design to install.